~funderscore blog cgit wiki get in touch
aboutsummaryrefslogtreecommitdiff
blob: 846caee7dfa418c90ede8bea98cbfb6034d14ed3 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/*
 * Copyright 2023 Toradex
 *
 * Common dtsi for Verdin AM62 SoM on Development carrier board
 *
 * https://www.toradex.com/computer-on-modules/verdin-arm-family/ti-am62
 * https://www.toradex.com/products/carrier-board/verdin-development-board-kit
 */

/* Verdin ETHs */
&cpsw3g {
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_rgmii1>, <&pinctrl_rgmii2>;
	status = "okay";
};

/* MDIO, shared by Verdin ETH_1 (On-module PHY) and Verdin ETH_2_RGMII */
&cpsw3g_mdio {
	status = "okay";

	cpsw3g_phy1: ethernet-phy@7 {
		compatible = "ethernet-phy-ieee802.3-c22";
		reg = <7>;
		interrupt-parent = <&main_gpio0>;
		interrupts = <38 IRQ_TYPE_EDGE_FALLING>;
		pinctrl-names = "default";
		pinctrl-0 = <&pinctrl_eth2_rgmii_int>;
		micrel,led-mode = <0>;
	};
};

/* Verdin ETH_1 (On-module PHY) */
&cpsw_port1 {
	status = "okay";
};

/* Verdin ETH_2_RGMII */
&cpsw_port2 {
	phy-handle = <&cpsw3g_phy1>;
	phy-mode = "rgmii-rxid";
	status = "okay";
};

/* Verdin PWM_1, PWM_2 */
&epwm0 {
	status = "okay";
};

/* Verdin PWM_3_DSI */
&epwm1 {
	status = "okay";
};

&main_gpio0 {
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_ctrl_sleep_moci>,
		    <&pinctrl_gpio_5>,
		    <&pinctrl_gpio_6>,
		    <&pinctrl_gpio_7>,
		    <&pinctrl_gpio_8>;
};

/* Verdin I2C_1 */
&main_i2c1 {
	status = "okay";

	/* IO Expander */
	gpio_expander_21: gpio@21 {
		compatible = "nxp,pcal6416";
		reg = <0x21>;
		#gpio-cells = <2>;
		gpio-controller;
	};

	/* Current measurement into module VCC */
	hwmon@40 {
		compatible = "ti,ina219";
		reg = <0x40>;
		shunt-resistor = <10000>;
	};

	/* Temperature sensor */
	sensor@4f {
		compatible = "ti,tmp75c";
		reg = <0x4f>;
	};

	/* EEPROM */
	eeprom@57 {
		compatible = "st,24c02", "atmel,24c02";
		reg = <0x57>;
		pagesize = <16>;
	};
};

/* Verdin I2C_2_DSI */
&main_i2c2 {
	status = "okay";
};

/* Verdin I2C_4_CSI */
&main_i2c3 {
	status = "okay";
};

/* Verdin CAN_1 */
&main_mcan0 {
	status = "okay";
};

/* Verdin SPI_1 */
&main_spi1 {
	status = "okay";
};

/* Verdin UART_3 */
&main_uart0 {
	status = "okay";
};

/* Verdin UART_1, connector X50 through RS485 transceiver. */
&main_uart1 {
	linux,rs485-enabled-at-boot-time;
	rs485-rx-during-tx;
	status = "okay";
};

/* Verdin I2S_1 */
&mcasp0 {
	status = "okay";
};

&mcu_gpio0 {
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_gpio_1>,
		    <&pinctrl_gpio_2>,
		    <&pinctrl_gpio_3>,
		    <&pinctrl_gpio_4>;
};

/* Verdin I2C_3_HDMI */
&mcu_i2c0 {
	status = "okay";
};

/* Verdin UART_4 */
&mcu_uart0 {
	status = "okay";
};

/* Verdin QSPI_1 */
&ospi0 {
	status = "okay";
};

/* Verdin SD_1 */
&sdhci1 {
	ti,driver-strength-ohm = <33>;
	status = "okay";
};

/* Verdin USB_1 */
&usbss0 {
	status = "okay";
};

&usb0 {
	status = "okay";
};

/* Verdin USB_2 */
&usbss1 {
	status = "okay";
};

&usb1 {
	status = "okay";
};

/* Verdin CTRL_WAKE1_MICO# */
&verdin_gpio_keys {
	status = "okay";
};

/* Verdin UART_2 */
&wkup_uart0 {
	/* FIXME: WKUP UART0 is used by DM firmware */
	status = "reserved";
};