1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
|
// SPDX-License-Identifier: GPL-2.0-or-later
/*
* Copyright 2018-2019, 2021 NXP
*
*/
#include <common.h>
#include <hang.h>
#include <init.h>
#include <log.h>
#include <spl.h>
#include <asm/global_data.h>
#include <asm/arch/clock.h>
#include <asm/arch/imx8mp_pins.h>
#include <asm/arch/sys_proto.h>
#include <asm/mach-imx/boot_mode.h>
#include <asm/mach-imx/gpio.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/mach-imx/mxc_i2c.h>
#include <asm/arch/ddr.h>
#include <power/pmic.h>
#include <power/pca9450.h>
#include <dm/uclass.h>
#include <dm/device.h>
DECLARE_GLOBAL_DATA_PTR;
int spl_board_boot_device(enum boot_device boot_dev_spl)
{
return BOOT_DEVICE_BOOTROM;
}
void spl_dram_init(void)
{
ddr_init(&dram_timing);
}
void spl_board_init(void)
{
arch_misc_init();
/*
* Set GIC clock to 500Mhz for OD VDD_SOC. Kernel driver does
* not allow to change it. Should set the clock after PMIC
* setting done. Default is 400Mhz (system_pll1_800m with div = 2)
* set by ROM for ND VDD_SOC
*/
clock_enable(CCGR_GIC, 0);
clock_set_target_val(GIC_CLK_ROOT, CLK_ROOT_ON | CLK_ROOT_SOURCE_SEL(5));
clock_enable(CCGR_GIC, 1);
puts("Normal Boot\n");
}
#define I2C_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE | PAD_CTL_PE)
#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
struct i2c_pads_info i2c_pad_info1 = {
.scl = {
.i2c_mode = MX8MP_PAD_I2C1_SCL__I2C1_SCL | PC,
.gpio_mode = MX8MP_PAD_I2C1_SCL__GPIO5_IO14 | PC,
.gp = IMX_GPIO_NR(5, 14),
},
.sda = {
.i2c_mode = MX8MP_PAD_I2C1_SDA__I2C1_SDA | PC,
.gpio_mode = MX8MP_PAD_I2C1_SDA__GPIO5_IO15 | PC,
.gp = IMX_GPIO_NR(5, 15),
},
};
#if CONFIG_IS_ENABLED(POWER_LEGACY)
#define I2C_PMIC 0
int power_init_board(void)
{
struct pmic *p;
int ret;
ret = power_pca9450_init(I2C_PMIC, 0x25);
if (ret)
printf("power init failed");
p = pmic_get("PCA9450");
pmic_probe(p);
/* BUCKxOUT_DVS0/1 control BUCK123 output */
pmic_reg_write(p, PCA9450_BUCK123_DVS, 0x29);
/*
* increase VDD_SOC to typical value 0.95V before first
* DRAM access, set DVS1 to 0.85v for suspend.
* Enable DVS control through PMIC_STBY_REQ and
* set B1_ENMODE=1 (ON by PMIC_ON_REQ=H)
*/
#ifdef CONFIG_IMX8M_VDD_SOC_850MV
/* set DVS0 to 0.85v for special case*/
pmic_reg_write(p, PCA9450_BUCK1OUT_DVS0, 0x14);
#else
pmic_reg_write(p, PCA9450_BUCK1OUT_DVS0, 0x1C);
#endif
pmic_reg_write(p, PCA9450_BUCK1OUT_DVS1, 0x14);
pmic_reg_write(p, PCA9450_BUCK1CTRL, 0x59);
/* Kernel uses OD/OD freq for SOC */
/* To avoid timing risk from SOC to ARM,increase VDD_ARM to OD voltage 0.95v */
pmic_reg_write(p, PCA9450_BUCK2OUT_DVS0, 0x1C);
return 0;
}
#endif
#ifdef CONFIG_SPL_LOAD_FIT
int board_fit_config_name_match(const char *name)
{
/* Just empty function now - can't decide what to choose */
debug("%s: %s\n", __func__, name);
return 0;
}
#endif
/* Do not use BSS area in this phase */
void board_init_f(ulong dummy)
{
int ret;
arch_cpu_init();
init_uart_clk(1);
ret = spl_early_init();
if (ret) {
debug("spl_init() failed: %d\n", ret);
hang();
}
preloader_console_init();
enable_tzc380();
setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
power_init_board();
/* DDR initialization */
spl_dram_init();
}
|