1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
|
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2018
* Lukasz Majewski, DENX Software Engineering, lukma@denx.de
*/
#include <common.h>
#include <init.h>
#include <asm/global_data.h>
#include <asm/io.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/clock.h>
#include <asm/arch/iomux-mx53.h>
#include <asm/arch/clock.h>
#include <asm/gpio.h>
#include <env.h>
#include <power/pmic.h>
#include <fsl_pmic.h>
#include <bootstage.h>
#include "kp_id_rev.h"
#define BOOSTER_OFF IMX_GPIO_NR(2, 23)
#define LCD_BACKLIGHT IMX_GPIO_NR(1, 1)
#define KEY1 IMX_GPIO_NR(2, 26)
#define LED_RED IMX_GPIO_NR(3, 28)
DECLARE_GLOBAL_DATA_PTR;
int dram_init(void)
{
u32 size;
size = get_ram_size((void *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE);
gd->ram_size = size;
return 0;
}
int dram_init_banksize(void)
{
gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE;
return 0;
}
static int power_init(void)
{
struct udevice *dev;
int ret;
ret = pmic_get("mc34708@8", &dev);
if (ret) {
printf("%s: mc34708 not found !\n", __func__);
return ret;
}
/* Set VDDGP to 1.110V for 800 MHz on SW1 */
pmic_clrsetbits(dev, REG_SW_0, SWx_VOLT_MASK_MC34708,
SWx_1_110V_MC34708);
/* Set VCC as 1.30V on SW2 */
pmic_clrsetbits(dev, REG_SW_1, SWx_VOLT_MASK_MC34708,
SWx_1_300V_MC34708);
/* Set global reset timer to 4s */
pmic_clrsetbits(dev, REG_POWER_CTL2, TIMER_MASK_MC34708,
TIMER_4S_MC34708);
return ret;
}
static void setup_clocks(void)
{
int ret;
u32 ref_clk = MXC_HCLK;
/*
* CPU clock set to 800MHz and DDR to 400MHz
*/
ret = mxc_set_clock(ref_clk, 800, MXC_ARM_CLK);
if (ret)
printf("CPU: Switch CPU clock to 800MHZ failed\n");
ret = mxc_set_clock(ref_clk, 400, MXC_PERIPH_CLK);
ret |= mxc_set_clock(ref_clk, 400, MXC_DDR_CLK);
if (ret)
printf("CPU: Switch DDR clock to 400MHz failed\n");
}
static void setup_ups(void)
{
gpio_request(BOOSTER_OFF, "BOOSTER_OFF");
gpio_direction_output(BOOSTER_OFF, 0);
}
int board_early_init_f(void)
{
return 0;
}
/*
* Do not overwrite the console
* Use always serial for U-Boot console
*/
int overwrite_console(void)
{
return 1;
}
int board_init(void)
{
gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
return 0;
}
void board_disable_display(void)
{
gpio_request(LCD_BACKLIGHT, "LCD_BACKLIGHT");
gpio_direction_output(LCD_BACKLIGHT, 0);
}
void board_misc_setup(void)
{
gpio_request(KEY1, "KEY1_GPIO");
gpio_direction_input(KEY1);
if (gpio_get_value(KEY1))
env_set("key1", "off");
else
env_set("key1", "on");
}
int board_late_init(void)
{
int ret = 0;
board_disable_display();
setup_ups();
if (!power_init())
setup_clocks();
ret = read_eeprom();
if (ret)
printf("Error %d reading EEPROM content!\n", ret);
show_eeprom();
read_board_id();
board_misc_setup();
return ret;
}
#if CONFIG_IS_ENABLED(BOOTSTAGE)
#define GPIO_DR 0x0
#define GPIO_GDIR 0x4
#define GPIO_ALT1 0x1
#define GPIO5_BASE 0x53FDC000
#define IOMUXC_EIM_WAIT 0x53FA81E4
/* Green LED: GPIO5_0 */
#define GPIO_GREEN BIT(0)
void show_boot_progress(int status)
{
/*
* This BOOTSTAGE_ID is called at very early stage of execution. DM gpio
* is not yet initialized.
*/
if (status == BOOTSTAGE_ID_START_UBOOT_F) {
/*
* After ROM execution the EIM_WAIT PAD is set as ALT0
* (according to RM it shall be ALT1 after reset). To use it as
* GPIO we need to set it to ALT1.
*/
setbits_le32(((uint32_t *)(IOMUXC_EIM_WAIT)), GPIO_ALT1);
/* Configure green LED GPIO pin direction */
setbits_le32(((uint32_t *)(GPIO5_BASE + GPIO_GDIR)),
GPIO_GREEN);
/* Turn on green LED */
setbits_le32(((uint32_t *)(GPIO5_BASE + GPIO_DR)), GPIO_GREEN);
}
/*
* This BOOTSTAGE_ID is called just before handling execution to kernel
* - i.e. gpio subsystem is already initialized
*/
if (status == BOOTSTAGE_ID_BOOTM_HANDOFF) {
/*
* Off green LED - the same approach - i.e. non dm gpio
* (*bits_le32) is used as in the very early stage.
*/
clrbits_le32(((uint32_t *)(GPIO5_BASE + GPIO_DR)),
GPIO_GREEN);
/*
* On red LED
*/
gpio_request(LED_RED, "LED_RED_ERROR");
gpio_direction_output(LED_RED, 1);
}
}
#endif
|