blob: 6f03de239e6073d11e95858d84b58f0f7c4166ee (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
|
This file contains information for VSC9953, a Vitesse L2 Switch IP
which is integrated in the T1040/T1020 Freescale SoCs.
About Device:
=============
VSC9953 is an 8-port Gigabit Ethernet switch supports the following features:
- 8192 MAC addresses
- Static Address provisioning
- Dynamic learning of MAC addresses and aging
- 4096 VLANs
- Independent and shared VLAN learning (IVL, SVL)
- Policing with storm control and MC/BC protection
- IPv4 and IPv6 multicast
- Jumbo frames (9.6 KB)
- Access Control List
- VLAN editing, translation and remarking
- RMON counters per port
Switch interfaces:
- 8 Gigabit switch ports (ports 0 to 7) are external and are connected to external PHYs
- 2 switch ports (ports 8 and 9) of 2.5 G are connected (fixed links)
to FMan ports (FM1@DTSEC1 and FM1@DTSEC2)
Commands Overview:
=============
Commands supported
- enable/disable a port or show its configuration (speed, duplexity, status, etc.)
- port statistics
- MAC learning
- add/remove FDB entries
- Port-based VLAN
- Private/Shared VLAN learning
- VLAN ingress filtering
- Port LAG
Commands syntax
ethsw [port <port_no>] { enable | disable | show } - enable/disable a port; show a port's configuration
ethsw [port <port_no>] statistics { [help] | [clear] } - show an l2 switch port's statistics
ethsw [port <port_no>] learning { [help] | show | auto | disable } - enable/disable/show learning configuration on a port
ethsw [port <port_no>] [vlan <vid>] fdb { [help] | show | flush | { add | del } <mac> } - add/delete a mac entry in FDB; use show to see FDB entries;
if [vlan <vid>] is missing, VID 1 will be used
ethsw [port <port_no>] pvid { [help] | show | <pvid> } - set/show PVID (ingress and egress VLAN tagging) for a port
ethsw [port <port_no>] vlan { [help] | show | add <vid> | del <vid> } - add a VLAN to a port (VLAN members)
ethsw [port <port_no>] untagged { [help] | show | all | none | pvid } - set egress tagging mode for a port
ethsw [port <port_no>] egress tag { [help] | show | pvid | classified } - configure VID source for egress tag.
Tag's VID could be the frame's classified VID or the PVID of the port
ethsw vlan fdb { [help] | show | shared | private } - make VLAN learning shared or private
ethsw [port <port_no>] ingress filtering { [help] | show | enable | disable } - enable/disable VLAN ingress filtering on port
ethsw [port <port_no>] aggr { [help] | show | <lag_group_no> } - get/set LAG group for a port
=> ethsw show
Port Status Link Speed Duplex
0 enabled down 10 half
1 enabled down 10 half
2 enabled down 10 half
3 enabled up 1000 full
4 disabled down - half
5 disabled down - half
6 disabled down - half
7 disabled down - half
8 enabled up 2500 full
9 enabled up 2500 full
=>
|