1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
|
MediaTek Gen2 PCIe controller
Required properties:
- compatible: Should contain one of the following strings:
"mediatek,mt7623-pcie"
- device_type: Must be "pci"
- reg: Base addresses and lengths of the PCIe subsys and root ports.
- reg-names: Names of the above areas to use during resource lookup.
- #address-cells: Address representation for root ports (must be 3)
- #size-cells: Size representation for root ports (must be 2)
- clocks: Must contain an entry for each entry in clock-names.
- clock-names:
Mandatory entries:
- sys_ckN :transaction layer and data link layer clock
Required entries for MT7623:
- free_ck :for reference clock of PCIe subsys
where N starting from 0 to one less than the number of root ports.
- phys: List of PHY specifiers (used by generic PHY framework).
- phy-names : Must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the
number of PHYs as specified in *phys* property.
- power-domains: A phandle and power domain specifier pair to the power domain
which is responsible for collapsing and restoring power to the peripheral.
- bus-range: Range of bus numbers associated with this controller.
- ranges: Ranges for the PCI memory and I/O regions.
Required properties for MT7623:
- #interrupt-cells: Size representation for interrupts (must be 1)
- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties
Please refer to the standard PCI bus binding document for a more detailed
explanation.
- resets: Must contain an entry for each entry in reset-names.
- reset-names: Must be "pcie-rst0", "pcie-rst1", "pcie-rstN".. based on the
number of root ports.
In addition, the device tree node must have sub-nodes describing each
PCIe port interface, having the following mandatory properties:
Required properties:
- device_type: Must be "pci"
- reg: Only the first four bytes are used to refer to the correct bus number
and device number.
- #address-cells: Must be 3
- #size-cells: Must be 2
- #interrupt-cells: Must be 1
- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties
Please refer to the standard PCI bus binding document for a more detailed
explanation.
- ranges: Sub-ranges distributed from the PCIe controller node. An empty
property is sufficient.
Examples for MT7623:
hifsys: syscon@1a000000 {
compatible = "mediatek,mt7623-hifsys",
"syscon";
reg = <0x1a000000 0x1000>;
#clock-cells = <1>;
#reset-cells = <1>;
};
pcie: pcie@1a140000 {
compatible = "mediatek,mt7623-pcie";
device_type = "pci";
reg = <0x1a140000 0x1000>, /* PCIe shared registers */
<0x1a142000 0x1000>, /* Port0 registers */
<0x1a143000 0x1000>, /* Port1 registers */
<0x1a144000 0x1000>; /* Port2 registers */
reg-names = "subsys", "port0", "port1", "port2";
#address-cells = <3>;
#size-cells = <2>;
#interrupt-cells = <1>;
interrupt-map-mask = <0xf800 0 0 0>;
interrupt-map = <0x0000 0 0 0 &sysirq GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>,
<0x0800 0 0 0 &sysirq GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>,
<0x1000 0 0 0 &sysirq GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>;
clocks = <&topckgen CLK_TOP_ETHIF_SEL>,
<&hifsys CLK_HIFSYS_PCIE0>,
<&hifsys CLK_HIFSYS_PCIE1>,
<&hifsys CLK_HIFSYS_PCIE2>;
clock-names = "free_ck", "sys_ck0", "sys_ck1", "sys_ck2";
resets = <&hifsys HIFSYS_PCIE0_RST>,
<&hifsys HIFSYS_PCIE1_RST>,
<&hifsys HIFSYS_PCIE2_RST>;
reset-names = "pcie-rst0", "pcie-rst1", "pcie-rst2";
phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>,
<&pcie2_phy PHY_TYPE_PCIE>;
phy-names = "pcie-phy0", "pcie-phy1", "pcie-phy2";
power-domains = <&scpsys MT7623_POWER_DOMAIN_HIF>;
bus-range = <0x00 0xff>;
ranges = <0x81000000 0 0x1a160000 0x1a160000 0 0x00010000 /* I/O space */
0x83000000 0 0x60000000 0x60000000 0 0x10000000>; /* memory space */
pcie@0,0 {
reg = <0x0000 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &sysirq GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>;
ranges;
};
pcie@1,0 {
reg = <0x0800 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &sysirq GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>;
ranges;
};
pcie@2,0 {
reg = <0x1000 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0>;
interrupt-map = <0 0 0 0 &sysirq GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>;
ranges;
};
};
|