1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
|
// SPDX-License-Identifier: GPL-2.0+
/*
* Teranetics PHY drivers
*
* Copyright 2010-2011 Freescale Semiconductor, Inc.
* author Andy Fleming
*/
#include <common.h>
#include <phy.h>
#include <linux/delay.h>
#ifndef CONFIG_PHYLIB_10G
#error The Teranetics PHY needs 10G support
#endif
int tn2020_config(struct phy_device *phydev)
{
if (phydev->port == PORT_FIBRE) {
unsigned short restart_an = (MDIO_AN_CTRL1_RESTART |
MDIO_AN_CTRL1_ENABLE |
MDIO_AN_CTRL1_XNP);
u8 phy_hwversion;
/*
* bit 15:12 of register 30.32 indicates PHY hardware
* version. It can be used to distinguish TN80xx from
* TN2020. TN2020 needs write 0x2 to 30.93, but TN80xx
* needs 0x1.
*/
phy_hwversion = (phy_read(phydev, 30, 32) >> 12) & 0xf;
if (phy_hwversion <= 3) {
phy_write(phydev, 30, 93, 2);
phy_write(phydev, MDIO_MMD_AN, MDIO_CTRL1, restart_an);
} else {
phy_write(phydev, 30, 93, 1);
}
}
return 0;
}
int tn2020_startup(struct phy_device *phydev)
{
unsigned int timeout = 5 * 1000; /* 5 second timeout */
#define MDIO_PHYXS_LANE_READY (MDIO_PHYXS_LNSTAT_SYNC0 | \
MDIO_PHYXS_LNSTAT_SYNC1 | \
MDIO_PHYXS_LNSTAT_SYNC2 | \
MDIO_PHYXS_LNSTAT_SYNC3 | \
MDIO_PHYXS_LNSTAT_ALIGN)
/*
* Wait for the XAUI-SERDES lanes to align first. Under normal
* circumstances, this can take up to three seconds.
*/
while (--timeout) {
int reg = phy_read(phydev, MDIO_MMD_PHYXS, MDIO_PHYXS_LNSTAT);
if (reg < 0) {
printf("TN2020: Error reading from PHY at "
"address %u\n", phydev->addr);
break;
}
if ((reg & MDIO_PHYXS_LANE_READY) == MDIO_PHYXS_LANE_READY)
break;
udelay(1000);
}
if (!timeout) {
/*
* A timeout is bad, but it may not be fatal, so don't
* return an error. Display a warning instead.
*/
printf("TN2020: Timeout waiting for PHY at address %u to "
"align.\n", phydev->addr);
}
if (phydev->port != PORT_FIBRE)
return gen10g_startup(phydev);
/*
* The TN2020 only pretends to support fiber.
* It works, but it doesn't look like it works,
* so the link status reports no link.
*/
phydev->link = 1;
/* For now just lie and say it's 10G all the time */
phydev->speed = SPEED_10000;
phydev->duplex = DUPLEX_FULL;
return 0;
}
U_BOOT_PHY_DRIVER(tn2020) = {
.name = "Teranetics TN2020",
.uid = PHY_UID_TN2020,
.mask = 0xfffffff0,
.features = PHY_10G_FEATURES,
.mmds = (MDIO_DEVS_PMAPMD | MDIO_DEVS_PCS |
MDIO_DEVS_PHYXS | MDIO_DEVS_AN |
MDIO_DEVS_VEND1 | MDIO_DEVS_VEND2),
.config = &tn2020_config,
.startup = &tn2020_startup,
.shutdown = &gen10g_shutdown,
};
|