blob: 35e8ff057986578a34387205fc3f48cd62b9dfcc (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
|
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2016 Freescale Semiconductor, Inc.
* Copyright 2021 NXP
*/
#ifndef __LS1012AQDS_H__
#define __LS1012AQDS_H__
#include "ls1012a_common.h"
/* DDR */
#define CFG_SYS_SDRAM_SIZE 0x40000000
/*
* QIXIS Definitions
*/
#ifdef CONFIG_FSL_QIXIS
#define CFG_SYS_I2C_FPGA_ADDR 0x66
#define QIXIS_LBMAP_BRDCFG_REG 0x04
#define QIXIS_LBMAP_SWITCH 6
#define QIXIS_LBMAP_MASK 0x08
#define QIXIS_LBMAP_SHIFT 0
#define QIXIS_LBMAP_DFLTBANK 0x00
#define QIXIS_LBMAP_ALTBANK 0x08
#define QIXIS_RST_CTL_RESET 0x31
#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
#endif
/*
* I2C bus multiplexer
*/
#define I2C_MUX_PCA_ADDR_PRI 0x77
#define I2C_MUX_PCA_ADDR_SEC 0x76 /* Secondary multiplexer */
#define I2C_RETIMER_ADDR 0x18
#define I2C_MUX_CH_DEFAULT 0x8
#define I2C_MUX_CH_CH7301 0xC
#define I2C_MUX_CH5 0xD
#define I2C_MUX_CH7 0xF
#define I2C_MUX_CH_VOL_MONITOR 0xa
/*
* RTC configuration
*/
#define CFG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/
/* Voltage monitor on channel 2*/
#define I2C_VOL_MONITOR_ADDR 0x40
#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
#define I2C_VOL_MONITOR_BUS_V_OVF 0x1
#define I2C_VOL_MONITOR_BUS_V_SHIFT 3
#undef CFG_EXTRA_ENV_SETTINGS
#define CFG_EXTRA_ENV_SETTINGS \
"verify=no\0" \
"kernel_addr=0x01000000\0" \
"kernelheader_addr=0x600000\0" \
"scriptaddr=0x80000000\0" \
"scripthdraddr=0x80080000\0" \
"fdtheader_addr_r=0x80100000\0" \
"kernelheader_addr_r=0x80200000\0" \
"kernel_addr_r=0x96000000\0" \
"fdt_addr_r=0x90000000\0" \
"load_addr=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"kernelheader_size=0x40000\0" \
"console=ttyS0,115200\0" \
BOOTENV \
"boot_scripts=ls1012aqds_boot.scr\0" \
"boot_script_hdr=hdr_ls1012aqds_bs.out\0" \
"scan_dev_for_boot_part=" \
"part list ${devtype} ${devnum} devplist; " \
"env exists devplist || setenv devplist 1; " \
"for distro_bootpart in ${devplist}; do " \
"if fstype ${devtype} " \
"${devnum}:${distro_bootpart} " \
"bootfstype; then " \
"run scan_dev_for_boot; " \
"fi; " \
"done\0" \
"boot_a_script=" \
"load ${devtype} ${devnum}:${distro_bootpart} " \
"${scriptaddr} ${prefix}${script}; " \
"env exists secureboot && load ${devtype} " \
"${devnum}:${distro_bootpart} " \
"${scripthdraddr} ${prefix}${boot_script_hdr}; " \
"env exists secureboot " \
"&& esbc_validate ${scripthdraddr};" \
"source ${scriptaddr}\0" \
"qspi_bootcmd=echo Trying load from qspi..;" \
"sf probe 0:0 && sf read $load_addr " \
"$kernel_addr $kernel_size; env exists secureboot " \
"&& sf read $kernelheader_addr_r $kernelheader_addr " \
"$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
"bootm $load_addr#$board\0"
#ifdef CONFIG_TFABOOT
#undef QSPI_NOR_BOOTCOMMAND
#define QSPI_NOR_BOOTCOMMAND "run distro_bootcmd; run qspi_bootcmd; "\
"env exists secureboot && esbc_halt;"
#endif
#include <asm/fsl_secure_boot.h>
#endif /* __LS1012AQDS_H__ */
|