1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
|
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2011-2012
* Pali Rohár <pali@kernel.org>
*
* (C) Copyright 2010
* Alistair Buxton <a.j.buxton@gmail.com>
*
* Derived from Beagle Board code:
* (C) Copyright 2006-2008
* Texas Instruments.
* Richard Woodruff <r-woodruff2@ti.com>
* Syed Mohammed Khasim <x0khasim@ti.com>
*
* Configuration settings for the Nokia RX-51 aka N900.
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
*/
#include <asm/arch/cpu.h> /* get chip and board defs */
#include <asm/arch/omap.h>
#include <asm/arch/mem.h>
#include <linux/stringify.h>
/* Clock Defines */
#define V_OSCK 26000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK >> 1)
/*
* Hardware drivers
*/
/*
* NS16550 Configuration
*/
#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
#define CFG_SYS_NS16550_CLK V_NS16550_CLK
/*
* select serial console configuration
*/
#define CFG_SYS_NS16550_COM3 OMAP34XX_UART3
#define CFG_SYS_BAUDRATE_TABLE { 4800, 9600, 19200, 38400, 57600, 115200 }
#define GPIO_SLIDE 71
/*
* Board ONENAND Info.
*/
#define CFG_SYS_ONENAND_BASE ONENAND_MAP
/* Environment information */
#define CFG_EXTRA_ENV_SETTINGS \
"usbtty=cdc_acm\0" \
"stdin=usbtty,serial,keyboard\0" \
"stdout=usbtty,serial,vidconsole\0" \
"stderr=usbtty,serial,vidconsole\0" \
"slide=gpio input " __stringify(GPIO_SLIDE) "\0" \
"switchmmc=mmc dev ${mmcnum}\0" \
"kernaddr=0x82008000\0" \
"initrdaddr=0x84008000\0" \
"scriptaddr=0x86008000\0" \
"fileloadaddr=" __stringify(CONFIG_SYS_LOAD_ADDR) "\0" \
"fileload=${mmctype}load mmc ${mmcnum}:${mmcpart} " \
"${fileloadaddr} ${mmcfile}\0" \
"kernload=setenv fileloadaddr ${kernaddr};" \
"setenv mmcfile ${mmckernfile};" \
"run fileload\0" \
"initrdload=setenv fileloadaddr ${initrdaddr};" \
"setenv mmcfile ${mmcinitrdfile};" \
"run fileload\0" \
"scriptload=setenv fileloadaddr ${scriptaddr};" \
"setenv mmcfile ${mmcscriptfile};" \
"run fileload\0" \
"scriptboot=echo Running ${mmcscriptfile} from mmc " \
"${mmcnum}:${mmcpart} ...; source ${scriptaddr}\0" \
"kernboot=echo Booting ${mmckernfile} from mmc " \
"${mmcnum}:${mmcpart} ...; bootm ${kernaddr} || " \
"bootz ${kernaddr}\0" \
"kerninitrdboot=echo Booting ${mmckernfile} ${mmcinitrdfile} from mmc "\
"${mmcnum}:${mmcpart} ...; bootm ${kernaddr} ${initrdaddr} || " \
"bootz ${kernaddr} ${initrdaddr}\0" \
"attachboot=echo Booting attached kernel image ...;" \
"setenv setup_omap_atag 1;" \
"bootm ${attkernaddr} || bootz ${attkernaddr};" \
"setenv setup_omap_atag\0" \
"trymmcscriptboot=run switchmmc && run scriptload && run scriptboot\0" \
"trymmckernboot=run switchmmc && run kernload && run kernboot\0" \
"trymmckerninitrdboot=run switchmmc && run initrdload && " \
"run kernload && run kerninitrdboot\0" \
"trymmcpartboot=setenv mmcscriptfile boot.scr; run trymmcscriptboot;" \
"setenv mmckernfile uImage; run trymmckernboot;" \
"setenv mmckernfile zImage; run trymmckernboot\0" \
"trymmcallpartboot=setenv mmcpart 1; run trymmcpartboot;" \
"setenv mmcpart 2; run trymmcpartboot;" \
"setenv mmcpart 3; run trymmcpartboot;" \
"setenv mmcpart 4; run trymmcpartboot\0" \
"trymmcboot=if run switchmmc; then " \
"setenv mmctype fat;" \
"run trymmcallpartboot;" \
"setenv mmctype ext4;" \
"run trymmcallpartboot;" \
"fi\0" \
"emmcboot=setenv mmcnum 1; run trymmcboot\0" \
"sdboot=setenv mmcnum 0; run trymmcboot\0" \
"trymmcbootmenu=setenv mmctype fat && run trymmcscriptboot || " \
"setenv mmctype ext4 && run trymmcscriptboot\0" \
"preboot=setenv mmcpart 1; setenv mmcscriptfile bootmenu.scr;" \
"setenv mmcnum 0 && run trymmcbootmenu || " \
"setenv mmcnum 1 && run trymmcbootmenu;" \
"if run slide; then true; else " \
"setenv bootmenu_delay 0;" \
"setenv bootdelay 0;" \
"fi\0" \
"menucmd=bootmenu\0" \
"bootmenu_0=Attached kernel=run attachboot\0" \
"bootmenu_1=Internal eMMC=run emmcboot\0" \
"bootmenu_2=External SD card=run sdboot\0" \
"bootmenu_3=U-Boot boot order=boot\0" \
"bootmenu_delay=30\0" \
""
#define CFG_POSTBOOTMENU \
"echo;" \
"echo Extra commands:;" \
"echo run sdboot - Boot from SD card slot.;" \
"echo run emmcboot - Boot internal eMMC memory.;" \
"echo run attachboot - Boot attached kernel image.;" \
"echo"
/*
* OMAP3 has 12 GP timers, they can be driven by the system clock
* (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
* This rate is divided by a local divisor.
*/
#define CFG_SYS_TIMERBASE (OMAP34XX_GPT2)
/*
* Physical Memory Map
*/
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
/*
* FLASH and environment organization
*/
#define CFG_SYS_SDRAM_BASE PHYS_SDRAM_1
#define CFG_SYS_INIT_RAM_ADDR 0x4020f800
#define CFG_SYS_INIT_RAM_SIZE 0x800
/*
* Attached kernel image
*/
#define SDRAM_SIZE 0x10000000 /* 256 MB */
#define SDRAM_END (CFG_SYS_SDRAM_BASE + SDRAM_SIZE)
#define IMAGE_MAXSIZE 0x1FF800 /* 2 MB - 2 kB */
#define KERNEL_OFFSET 0x40000 /* 256 kB */
#define KERNEL_MAXSIZE (IMAGE_MAXSIZE-KERNEL_OFFSET)
#define KERNEL_ADDRESS (SDRAM_END-KERNEL_MAXSIZE)
/* Reserve protected RAM for attached kernel */
#define CFG_PRAM ((KERNEL_MAXSIZE >> 10)+1)
#endif /* __CONFIG_H */
|