blob: d10b88f157548c127971cadceb9541f5fc649b83 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
|
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2013 Freescale Semiconductor, Inc.
*
* Configuration settings for the Freescale Vybrid vf610twr board.
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <asm/arch/imx-regs.h>
#include <linux/stringify.h>
/* NAND support */
#ifdef CONFIG_CMD_NAND
#define CFG_SYS_NAND_BASE NFC_BASE_ADDR
/* Dynamic MTD partition support */
#endif
#define CFG_SYS_FSL_ESDHC_ADDR 0
#define CFG_FEC_MXC_PHYADDR 0
/* I2C Configs */
/*
* We do have 128MB of memory on the Vybrid Tower board. Leave the last
* 16MB alone to avoid conflicts with Cortex-M4 firmwares running from
* DDR3. Hence, limit the memory range for image processing to 112MB
* using bootm_size. All of the following must be within this range.
* We have the default load at 32MB into DDR (for the kernel), FDT at
* 64MB and the ramdisk 512KB above that (allowing for hopefully never
* seen large trees). This allows a reasonable split between ramdisk
* and kernel size, where the ram disk can be a bit larger.
*/
#define MEM_LAYOUT_ENV_SETTINGS \
"bootm_size=0x07000000\0" \
"loadaddr=0x82000000\0" \
"kernel_addr_r=0x82000000\0" \
"fdt_addr=0x84000000\0" \
"fdt_addr_r=0x84000000\0" \
"rdaddr=0x84080000\0" \
"ramdisk_addr_r=0x84080000\0"
#define CFG_EXTRA_ENV_SETTINGS \
MEM_LAYOUT_ENV_SETTINGS \
"script=boot.scr\0" \
"image=zImage\0" \
"console=ttyLP1\0" \
"fdt_file=vf610-twr.dtb\0" \
"boot_fdt=try\0" \
"ip_dyn=yes\0" \
"mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
"mmcpart=1\0" \
"mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
"update_sd_firmware_filename=u-boot.imx\0" \
"update_sd_firmware=" \
"if test ${ip_dyn} = yes; then " \
"setenv get_cmd dhcp; " \
"else " \
"setenv get_cmd tftp; " \
"fi; " \
"if mmc dev ${mmcdev}; then " \
"if ${get_cmd} ${update_sd_firmware_filename}; then " \
"setexpr fw_sz ${filesize} / 0x200; " \
"setexpr fw_sz ${fw_sz} + 1; " \
"mmc write ${loadaddr} 0x2 ${fw_sz}; " \
"fi; " \
"fi\0" \
"mmcargs=setenv bootargs console=${console},${baudrate} " \
"root=${mmcroot}\0" \
"loadbootscript=" \
"fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source\0" \
"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if run loadfdt; then " \
"bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
"bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi; " \
"else " \
"bootz; " \
"fi;\0" \
"netargs=setenv bootargs console=${console},${baudrate} " \
"root=/dev/nfs " \
"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
"netboot=echo Booting from net ...; " \
"run netargs; " \
"if test ${ip_dyn} = yes; then " \
"setenv get_cmd dhcp; " \
"else " \
"setenv get_cmd tftp; " \
"fi; " \
"${get_cmd} ${image}; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
"bootz ${loadaddr} - ${fdt_addr}; " \
"else " \
"if test ${boot_fdt} = try; then " \
"bootz; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"fi; " \
"else " \
"bootz; " \
"fi;\0"
/* Miscellaneous configurable options */
/* Physical memory map */
#define PHYS_SDRAM (0x80000000)
#define PHYS_SDRAM_SIZE (128 * 1024 * 1024)
#define CFG_SYS_SDRAM_BASE PHYS_SDRAM
#define CFG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
#define CFG_SYS_INIT_RAM_SIZE IRAM_SIZE
#endif
|