~funderscore blog cgit wiki get in touch
aboutsummaryrefslogtreecommitdiff
blob: 9655b666eda71a4ae354ee712b15c3649c51c9e4 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * Copyright (C) 2007-2013 Tensilica, Inc.
 * Copyright (C) 2014 - 2016 Cadence Design Systems Inc.
 */

#ifndef __CONFIG_H
#define __CONFIG_H

#include <asm/arch/core.h>
#include <asm/addrspace.h>
#include <asm/config.h>

/*
 * The 'xtfpga' board describes a set of very similar boards with only minimal
 * differences.
 */

/*===================*/
/* RAM Layout        */
/*===================*/

#if XCHAL_HAVE_PTP_MMU
#define CFG_SYS_MEMORY_BASE		\
	(XCHAL_VECBASE_RESET_VADDR - XCHAL_VECBASE_RESET_PADDR)
#define CFG_SYS_IO_BASE		0xf0000000
#else
#define CFG_SYS_MEMORY_BASE		0x60000000
#define CFG_SYS_IO_BASE		0x90000000
#define CFG_MAX_MEM_MAPPED		0x10000000
#endif

/* Onboard RAM sizes:
 *
 * LX60		0x04000000		  64 MB
 * LX110	0x03000000		  48 MB
 * LX200	0x06000000		  96 MB
 * ML605	0x18000000		 384 MB
 * KC705	0x38000000		 896 MB
 *
 * noMMU configurations can only see first 256MB of onboard memory.
 */

#if XCHAL_HAVE_PTP_MMU || CONFIG_BOARD_SDRAM_SIZE < 0x10000000
#define CFG_SYS_SDRAM_SIZE		CONFIG_BOARD_SDRAM_SIZE
#else
#define CFG_SYS_SDRAM_SIZE		0x10000000
#endif

#define CFG_SYS_SDRAM_BASE		MEMADDR(0x00000000)

/* Lx60 can only map 128kb memory (instead of 256kb) when running under OCD */

/* Memory test is destructive so default must not overlap vectors or U-Boot*/

#if defined(CFG_MAX_MEM_MAPPED) && \
	CFG_MAX_MEM_MAPPED < CFG_SYS_SDRAM_SIZE
#define XTENSA_SYS_TEXT_ADDR		\
	(MEMADDR(CFG_MAX_MEM_MAPPED) - CONFIG_SYS_MONITOR_LEN)
#else
#define XTENSA_SYS_TEXT_ADDR		\
	(MEMADDR(CFG_SYS_SDRAM_SIZE) - CONFIG_SYS_MONITOR_LEN)
#endif

/*==============================*/
/* U-Boot general configuration */
/*==============================*/

	/* Console I/O Buffer Size  */
/*==============================*/
/* U-Boot autoboot configuration */
/*==============================*/


/*=========================================*/
/* FPGA Registers (board info and control) */
/*=========================================*/

/*
 * These assume FPGA bitstreams from Tensilica release RB and up. Earlier
 * releases may not provide any/all of these registers or at these offsets.
 * Some of the FPGA registers are broken down into bitfields described by
 * SHIFT left amount and field WIDTH (bits), and also by a bitMASK.
 */

/* FPGA core clock frequency in Hz (also input to UART) */
#define CFG_SYS_FPGAREG_FREQ	IOADDR(0x0D020004)	/* CPU clock frequency*/

/*
 * DIP switch (left=sw1=lsb=bit0, right=sw8=msb=bit7; off=0, on=1):
 *   Bits 0..5 set the lower 6 bits of the default ethernet MAC.
 *   Bit 6 is reserved for future use by Tensilica.
 *   Bit 7 maps the first 128KB of ROM address space at CFG_SYS_ROM_BASE to
 *   the base of flash * (when on/1) or to the base of RAM (when off/0).
 */
#define CFG_SYS_FPGAREG_DIPSW	IOADDR(0x0D02000C)
#define FPGAREG_MAC_SHIFT		0	/* Ethernet MAC bits 0..5 */
#define FPGAREG_MAC_WIDTH		6
#define FPGAREG_MAC_MASK		0x3f
#define FPGAREG_BOOT_SHIFT		7	/* Boot ROM addr mapping */
#define FPGAREG_BOOT_WIDTH		1
#define FPGAREG_BOOT_MASK		0x80
#define FPGAREG_BOOT_RAM		0
#define FPGAREG_BOOT_FLASH		(1<<FPGAREG_BOOT_SHIFT)

/* Force hard reset of board by writing a code to this register */
#define CFG_SYS_FPGAREG_RESET	IOADDR(0x0D020010) /* Reset board .. */
#define CFG_SYS_FPGAREG_RESET_CODE	0x0000DEAD   /*  by writing this code */

/*====================*/
/* Serial Driver Info */
/*====================*/

#define CFG_SYS_NS16550_COM1		IOADDR(0x0D050020) /* Base address */

/* Input clk to NS16550 (in Hz; the SYS_CLK_FREQ is in kHz) */
#define CFG_SYS_NS16550_CLK		get_board_sys_clk()

/*======================*/
/* Ethernet Driver Info */
/*======================*/

#define CFG_ETHBASE			00:50:C2:13:6f:00
#define CFG_SYS_ETHOC_BASE		IOADDR(0x0d030000)
#define CFG_SYS_ETHOC_BUFFER_ADDR	IOADDR(0x0D800000)

/*=====================*/
/* Flash & Environment */
/*=====================*/

#ifdef CONFIG_XTFPGA_LX60
# define CFG_SYS_FLASH_SIZE		0x0040000	/* 4MB */
# define CFG_SYS_FLASH_PARMSECT_SZ	0x2000		/* param size  8KB */
# define CFG_SYS_FLASH_BASE		IOADDR(0x08000000)
#elif defined(CONFIG_XTFPGA_KC705)
# define CFG_SYS_FLASH_SIZE		0x8000000	/* 128MB */
# define CFG_SYS_FLASH_PARMSECT_SZ	0x8000		/* param size 32KB */
# define CFG_SYS_FLASH_BASE		IOADDR(0x00000000)
#else
# define CFG_SYS_FLASH_SIZE		0x1000000	/* 16MB */
# define CFG_SYS_FLASH_PARMSECT_SZ	0x8000		/* param size 32KB */
# define CFG_SYS_FLASH_BASE		IOADDR(0x08000000)
#endif

/*
 * Put environment in top block (64kB)
 * Another option would be to put env. in 2nd param block offs 8KB, size 8KB
 */

/* print 'E' for empty sector on flinfo */

#endif /* __CONFIG_H */